Futaba GV-1 Instrukcja Użytkownika Strona 20
- Strona / 49
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2222
2222
22
ASSEMBLY & ADJUSTMENT
Fuselage setting precautions
Throttle servo linkage precautions
To effectively use the governor, observe the following precautions when con-
necting the servo linkage.
-Make the servo operating range as wide as possible.
Make the throw of the transmitter ATV function, AFR function, and func-
tions as close as possible to 100%. The governor will not operate at throws
lower than 50%.
-Do not use the throttle curve. Operate the throttle linearly.
-Fly with the governor turned OFF and adjust the needle so that the
engine smoothly reacts to movement of the transmitter stick.
If there is a point at which the reaction of the engine is considerably differ-
ent due to a too rich or too lean mixture, the governor may not operate to
its maximum potential..
Use of a tuned silencer
The use of a tuned pipe type silencer may cause the engine throttle
response to be substantially different from that with a normal muffler.
Adjust the needle (and pipe length) so that engine speed changes are
proportional to the throttle opening. If the engine speed does not
change linearly, the governor will not perform satisfactorily with a muf-
fler or a pipe that does not allow the carburetion to be linear.
Fuselage vibration countermeasures
If the helicopter frame is weak, or the engine mount is deformed or not
installed properly, the vibrations applied to the engine will increase.
Engine vibrations will lead to unstable speed and prevent the governor
from maximum performance. Therefore, make sure that the engine is
vibration free and that the carburetor is of good liner design because
the governor cannot correct engine problems.
- INSTRUCTION MANUAL 1
- FOREWORD 2
- TABLE OF CONTENTS 3
- PRECAUTIONS 4
- Setting precautions 5
- Center of sensor 6
- Operating precautions 7
- BEFORE USE 8
- Nomenclature 9
- Set speed 10
- Examples 12
- Function 13
- Connection 13
- 3.7mm 3.7mm 14
- Distance from center 15
- Cooling fan 15
- Sensor mounting 16
- Magnet direction check 16
- Magnet mounting 17
- 4Recheck the sensor output 18
- GV-1 connections 19
- Fuselage setting precautions 20
- Control amp mounting 21
- FUNCTIONS 22
- Function map 23
- Throttle limit setting 24
- 2Input the gear ratio 25
- 2Set the switch to the de 25
- 2Set the variable resistor 25
- Battery fail safe setting 28
- Fail safe data setting 29
- Speed sensor output check 30
- 1Hold down the DATA+ or DATA 31
- Speed setting rS1~rS3 32
- Speed display mode Disp 33
- Rotor gear ratio GRt 33
- 1Operate the switch 34
- Governor ON/OFF condition 35
- (monitor function) SWCd 35
- Mixture rate setting MGx/MDx 38
- 2Set the rate with the 39
- 2Transfer the mixture 39
- Mixture ATV ATV 40
- Mixture servo reverse MSx 40
- 1Set the mode by pressing the 41
- Limit set Lmt 43
- 1Each time the DATA+ or DATA 44
- REFERENCE 45
- Glossary 46
- GV-1 PARAMETERS SHEET 47
- REPAIR SERVICE 48
- FUTABA CORPORATION 49
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Futaba GV-1
(2 strony)Whirlpool TUD5700 manuels
Manuels d'utilisation et guides de l'utilisateur pour Lave-vaisselle Whirlpool TUD5700.
Nous fournissons des manuels en pdf 2 Whirlpool TUD5700 à télécharger gratuitement par type de document : Guide d'utilisation et d'entretien, Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji