Futaba 14MZ Quick Start Guide - Helis Instrukcja Użytkownika Pobierz pdf

When turning on the 14MZ, you must let the system cycle through before turning off.

There is a sequence that should be followed to get you started.

R5014DPS Receiver

First you should know the 14MZ receiver (R5014DPS) has

a different layout than the standard layout Futaba has

used in the past. After you have all your servos installed in

your helicopter, you’ll want to use one of these charts to

plug the proper servos into the R5014DPS receiver.

H-4 Swash All Others

Ch 1 Throttle Throttle

Ch 2 Rudder Rudder

Ch 3 Aileron (Left/Right Cyclic) Gyro

Ch 4 Elevator 1 (Fore/Aft Cyclic) Aileron (Left/Right Cyclic)

Ch 5 Pitch Elevator (Fore/Aft Cyclic)

Ch 6 Elevator 2 Pitch

Ch 7 Gyro Governor 1

Ch 8 Governor 1 Governor 2

Ch 9 Governor 2 Needle

Ch 10 Needle Auxiliary 3

Ch 11 Auxiliary 2 Auxiliary 2

Ch 12 Auxiliary 1 Auxiliary 1

CHOOSING MODEL TYPE AND SWASH TYPE

After turning on the power switch and pressing No for transmit. This will take you to the Home Page. Press Linkage Menu

then Model Select then press New, and then pressYes. Press on Swash Type and choose from one of the 7 different Swash

Types in the diagram that corresponds with the type of control system on your helicopter. You’ll be asked “Check Change”, if

correct, press Yes.

After selecting the swash type you will come to the Frequency page. Select the frequency by pressing the Pink Box and then

select the frequency or channel you would like to be on for this particular model. After selecting the frequency, press Enter at

the top right hand corner of the screen. You’ll be asked to Check the change. If Yes, you’ll need to make sure you have your

battery plugged into the receiver but no power to the receiver. Once you press Yes, then turn on the power to the receiver to

program the receiver to the frequency you just selected. You must have the transmitter antenna very close to the receiver

antenna when doing this.

Please follow the steps in the manual on page (26) How to change the Frequency. Then you’ll need to turn off the power to

cycle through for the frequency to take affect.

Turn the system back on. Press “Yes” for Transmit. This will take you to the Home Page to start setting everything up.

System Menu

Model Menu

Linkage Menu

Direct Keys

1 2 3 4

Podsumowanie treści

Strona 1

When turning on the 14MZ, you must let the system cycle through before turning off.There is a sequence that should be followed to get you started.R501

Strona 2

SETTING SWASH MIXINGAt this time you should install and set up your servos as per the helicopter manufactures instructions.While at the Home Page, you

Strona 3

ACTIVATING CONDITIONSFrom the Home Page press Model Menu, select Condition Select. In the red box you’ll see the word Normal. This is yournormal hover

Strona 4

CHOOSING A PITCH AND THROTTLE CURVESYou have many types of curves tochoose from for both Throttle andPitch. From the Home Page, pressModel Menu and th

Komentarze do niniejszej Instrukcji

Brak uwag

Futaba 14MZ Quick Start Guide - Helis Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Akcesoria komunikacja Futaba 14MZ Quick Start Guide - Helis. Futaba 14MZ Quick Start Guide - Helis User Manual [fr] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Akcesoria komunikacja Futaba 14MZ Quick Start Guide - Helis