Futaba R203GF Instrukcja Użytkownika Pobierz pdf

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R203GF, complies with part15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2011, 3 (1)

R203GF Speciﬁcations:

(

S-FHSS/FHSS

system, 3-channel receiver)

•Receivingon2.4GHzband

•System:

S-FHSS/FHSS

system(autodetection)

S-FHSS

Normal/Highspeedmode(autodetection)

•

Operatingvoltage(Typ.):4.8V-7.4V(

sharedwithservo)

• F/SandBatteryF/Sfunction:Theoperationchannelsdifferaccordingtothetransmitterused.However,Battery

F/Sdoesn'tfunctionwhenitisusedwithFHSSandF/SbecomesonlyCH2.

• BatteryF/Svoltage:3.8V

•Currentdrain:30mA(atnosignal)

•Size:1.54x1.02x0.39”(39x26x10mm)

•Weight:0.28oz.(8g)

The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work

properly when other type battery is used.

󾛽

WARNING

󾛻

NEVERusedrybatteriesforthe

powersupplyoftheR203GF as they

maycausedifculties.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

Placethetransmitterandthereceiverclose

toeachotherwithinhalf(0.5)meter

Turnonthetransmitterandthereceiver.

PushandholdtheLinkswitchonthe

receiver.

Whenthelinkiscomplete,theLEDonthe

receiverchangestosolidgreen.

*Please referto the tablebelowfor LED status

andreceivercondition.

Nosignalreception LED:Off

Receivingsignals LED:On

Receivingsignals,butID

isunmatched.

LED:Blink

PowerOn,whenF/S

setsit.

LED:Early

Blinktherst

onesecond

*If there are many

S-FHSS/FHSS

 systems turned

onaroundyourreceiver,itmightnotlinktoyour

transmitter. Inthiscase, even ifthereceiver’s

LEDstayssolidgreen,unfortunatelythe

receivermighthaveestablishedalinktooneof

the other transmitters.This is very dangerous

ifyou donotnotice this situation.Inorder to

avoidtheproblem,westronglyrecommend

youto double-checkwhetheryourreceiveris

controlled by your transmitter bygiving throttle

input,etc.andthencheckingservoresponse.

󾛽

WARNING

󾛹

Afterthelinkingisdone,pleasecycle

receiverpowerandcheckifthereceiver

tobelinkedisreallyunderthecontrolbythe

transmittertobelinked.

󾛻

Donotperformthelinkingprocedure

withmotor'smainwireconnectedor

withtheengineoperatingasitmayresultin

seriousinjury.

Link switch LED

Battery terminal (B)

Ch output (1 to 3)

Operating Precautions:

Once the

R203GF

detectsthe

S-FHSS

normalmode,

S-FHSS

highspeed

modeor

FHSS

mode,thedetected

modeislockedaslongasthe

powerisON.Whenneedtochange

themode,pleasecyclepower.

Note:

The R203GF is compatible with the S-FHSS or FHSS

system transmitters .

*Futaba S-FHSS/FHSS system does not work with current Futaba FASST system.

Usage condition on "High Speed mode"

󾛽

CAUTION

󾛹

Whenusingthehigh-speedmode,useaFutaba

digitalservo(includingbrushlessservo).Analog

servoscannotbeused.

•Theuseofanalogservosmaycauseservotrouble.

1M23N17445

S-FHSS/FHSS-2.4GHz

system

(Auto Detection),

3-channel receiver

Thank you for purchasing the

R203GF

receiver.

The

R203GF

is designed for use with the Futaba

S-FHSS

FHSS

system transmitter. The

S-FHSS

system has two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the

peripherals as the frame rate of the output is 13.6ms.

The "High Speed mode" only accepts the digital

servos, including BLS series, and most peripheral

equipments such as the brushless ESCs. The frame

rate of the outputs is 6.8ms. However, there is a

transmitter that cannot correspond, too.

Please pay special attention to the information

contained within this manual and transmitter's manual

in order to have a pleasant running/ying experience.

The R203GF is compatible with the S-FHSS or FHSS

system transmitters

R203GF

Podsumowanie treści

Strona 1 - Ch output (1 to 3)

Compliance Information Statement (for U.S.A.)This device, trade name Futaba Corporation of America, model number R203GF, complies with part15 of the F

Komentarze do niniejszej Instrukcji

Brak uwag

Futaba R203GF Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Akcesoria komunikacja Futaba R203GF. Futaba R203GF User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Akcesoria komunikacja Futaba R203GF